Back to blog

    Replacing a $20 Audi Avant Latch With a 2-Gram 3D Print

    ·5 min read
    On 1998–2008 Audi Avants, the warning triangle lives behind a small door in the tailgate's inner panel. A plastic latch holds that door shut, and sooner or later its tongue snaps off. After that the door flops open, often every time you open the tailgate. Owners try zip ties and superglue; the glue rarely lasts. The OEM part, 4B9 867 899 (listed as 4B98678994PK), is around $20 at the dealer and $10 to $18 from online parts shops, for something that weighs about 2 grams.
    We designed a printable replacement on a 2004 S4 Avant, and it's a free download on MakerWorld. This post covers which cars it fits, how we got the shape right, and the print settings, because the material is the part people get wrong.

    Which cars it fits

    Wagons only. The sedans don't have this compartment.
    • A4 / S4 Avant (B6, B7): 2002–2008
    • RS4 Avant (B7): 2006–2008
    • A6 / S6 Avant (C5): 1998–2005
    • A6 allroad (C5): 2001–2005
    • RS6 Avant (C5): 2003–2005
    It replaces OEM 4B9 867 899. Parts shops usually call it the "warning triangle case lock"; Audi's catalog lists it as a liftgate trim fastener. We've fitted it to a B6 S4 Avant; the other cars on the list use the same part number.

    Why the original breaks

    Age. After twenty years or so of summers in the back of a wagon, the original plastic is brittle. On ours, the tongue, the part of the latch that actually catches and holds the door shut, had snapped clean off. Without it, nothing holds the door closed.

    Getting the shape right

    The part is small, 35.3 × 19.4 × 7.9 mm, but it has three features that all have to line up. The knob you turn sits on the outside of the door, and a clip on its back passes through the door and snaps into the square hole in the latch, so the door panel is sandwiched between them. Turning the knob swings the latch, and its tongue catches to hold the door shut. A small post stops the knob from being turned too far.
    We measured the broken original with calipers, modeled it, and it took three test prints to get the fit right.
    The square hole is where fit matters most. Holes print slightly small on FDM printers, so the size in CAD is rarely the size you measured. Our guide to designing 3D-printed adapters goes through the test-coupon method we use to find the right clearance, and 3D printing tolerances has starting numbers.

    The material matters more than the shape

    A closed car in the sun gets hot inside, and the tailgate trim sits right under the rear glass. PLA starts to soften at around 55 to 65 °C, so a PLA latch can sag or let go after one summer afternoon. PETG holds up better but can still soften in the hottest cars.
    Print it in ASA (ABS works too). Both stay stiff well past the temperatures a car interior reaches, and ASA also resists UV.

    Print settings

    • Material: ASA or ABS
    • Orientation: flat side down, no supports
    • Layers: 0.2 mm
    • Walls: 4
    • Infill: 100%. It's only about 2 g, and a solid part is stiffer at the tab.
    There's a ready-made Bambu Studio print profile with these settings on the MakerWorld page.

    Fitting it

    The latch and the knob are held together by the knob's clips, and the plastic is stiff, so getting the old one off takes a little care.
    • 1. Open the door and find the back of the latch, where the knob's clips come through the square hole.
    • 2. Squeeze the clips together while pulling the latch away from the door. The plastic is stiff, so needle-nose pliers help. Go slowly so you don't break the knob's clips too.
    • 3. Line the new latch's square hole up with the clips, oriented the same way as the old one, and press it on until the clips snap through.
    • 4. Turn the knob and check that the tongue catches and the post stops it at the end of its travel.

    Small parts, real fixes

    Most cars have a few of these: a clip or latch the dealer sells for far more than it costs to make, or no longer sells at all. Measuring the broken original, checking the fit with a quick test print, and picking a material for where the part lives covers most of them. The DFM checklist for small enclosures covers the same thinking for larger housings.
    If you have a part like this that needs designing, or one that needs to be made in volume, tell us about it.